Page tree
Skip to end of metadata
Go to start of metadata
Log into the iMac with your EID and Password

go to the Motu Audio Setup and make sure the settings are correct
General settings

These are the correct settings for Audio Input and Output


Make sure set to Analog 1-2 on Input and Output

Go to the System Prefs and make sure the sound Output is set to the Motu 828Mk3 Hybrid USB
Same with the Input
Launch the Application Adobe Audition.

Go to the >Adobe > Preferences and check the Audio Hardware make sure it is set to the MOTU FOR THE DEFAULT INPUT AND OUTPUT


Next check the Audio Channel Mapping Make sure it is set to


MOTU 828mk3 Hybrid Analog 1 and Analog 2 Input


Output should be set to

MOTU 828mk3 Hybrid Analog 1 and Analog 6 Output


Make sure the Keypad to dial and answer calls is ON it should be left on but check it.

On the audio board, turn ON the microphones that you wish to record from.  


If you are only recording yourself, use the Mic 1.

The ON button should be lit up, and the slider moved approximately half way up.

Now is the time to adjust your levels.

Practice your recording and adjust the microphone slider until the levels average -7db on the meter that reads "out to recorders" at the top of the audio board.

This step has the most impact on the quality of your recording.  


Make sure that your audio levels are never too high to go off the chart or too low as to barely register.  

Put the headphones attached to the audio board on your ears.

Make sure the "TEL" button is lit

All the buttons with Arrows should be lit RED on each mic in use

On the audio board, turn the Phone mic On.

On the small telephone keypad, press the Red Button to Drop any previous calls.


Then press the yellow Call button to pickup the telephone line

Dial 9 to reach an outside line.

You should hear a dial tone. If you don't hear a dial tone hit the red button and then the yellow Call button again.


make sure the Phone line is on on the audio board too. . .

Dial your telephone number as normal:

Area code first, then the 7 digit phone number.

If you want the person to call in for the interview instead of calling out to them -


The phone number to this phone line is 512.232.3236.

The Yellow Call button will flash when a call is incoming


Press the Yellow button to answer the incoming call. You should hear the person on the "Phone" channel

A. In Adobe Audition, select File > New > Audio File ... (Shift + Command + N)

B. Press OK to accept the default settings.
C. Press the red record button to begin your recording.
D. Press the red record button again to stop your recording. 
To record again, repeat the above A through D steps. 
To hang up your call, press the red Drop button.



Press the ON button for the iMac recorder on & move the slider up.

This will route the computer audio through the headphones.


To record audio again, turn the iMac slider OFF.

To route audio through the speakers, turn OFF Mics 1 through 4 on the sound board.

Press play to hear your recording.

If you do not hear audio:

  • Make sure that the Mics 1 through 4 are turned off. 
  • Turn up the volume on the Monitor knob.


When you're done, in Adobe Audition, select the File you wish to export.
Select File > Export > File
Name your file.
Select Browse to choose a location to save the file.
In the 'Where' dropdown menu, select the Desktop.

Under File format, WAV is the default. If you would prefer MP3 files, select MP3.

Note: WAV files are far superior for editing or any kind.

Select Save.
Select OK.
Repeat this process if you have recorded multiple files that you wish to save. 
Quit out of Adobe Audition. You do not need to save changes to this project if you have only made simple recordings.
Save your audio recordings by copying them from the Desktop to a USB device or one of the Servers available under Shares.



  File Modified
PDF File RM3-USERMANUAL-FINAL.pdf iKey RM3 User Manual Sep 10, 2014 by Joshua W Kinney