>>> Reserve a Laser Cutter <<<
- If the laser cutter
Acrylic Laser Cutting Hours
|9 PM - 10 PM||Monday - Thursday|
|1 PM - 6 PM||Saturday|
How to Prepare Your File
How to Use the Laser Cutter
Laser Cutter Policies
- computers aren't logged in, notify staff at the Technology Desk. Only the Technology Desk staff are permitted to give you access to the system. Do not log in using your own EID credentials, as the software is only configured under our account.
- Infractions of laser cutter or any other Technology Lab policies will result in privileges being revoked.
- Operating the laser cutter without being trained AND paying the subscription for the semester will result in privileges being revoked.
- If you notice that the laser cutter requires cleaning or maintenance, please notify the Technology Desk staff immediately in person or by calling 512-471-1189.
Certification and Subscription
- In order to use the laser cutter cutters the student, faculty, or staff must (1) have gone through a laser cutter training session for the laser cutter in question and (2) have a valid reservation made through IO Central.
- Reservations for the laser cutter must be made in person at IO Central and the cost is $5.00 per hour.
- The minimum reservation length is 30 minutes, the maximum reservation length is 3 hours.
- Each user is limited to a maximum of 3 hours per week of laser cutter reservations. Each week begins when the lab opens Sunday and ends at lab closing on Saturday night. Same-day reservations do not count against your weekly limit and may be reserved without any limits.
- During times of high use, a wait list will be made available in IO Central. If you do not arrive within 15 minutes of your scheduled start time, IO staff will make the laser cutter available to the top of the wait list. If you are going to be more than 15 minutes late for your reservation, call IO Central at 471-4817 to avoid losing the rest of your time.
- If you notice that the laser cutter requires cleaning or maintenance, please notify IO Central at 471-1189 immediately, any reservation time lost to maintenance or cleaning will be reimbursed with equivalent time or with returned bevobucks
- be a member of the School of Architecture community (students, faculty, or staff) AND
- purchase a subscription for the semester AND
- complete online laser cutter training AND
- be certified for laser cutter use by a member of the Technology Desk staff.
Health and Safety
- Although this system uses a CO2 laser that could damage your eyes or skin with direct contact, it uses both a system of safety interlocks and an IR-absorbing window on the top door, making the laser cutter safe to use without goggles or other safety gear.
- Please note that the intense light that appears during the engraving or cutting process is the product of material combustion or vaporization. DO NOT STARE AT THE BRIGHT LIGHT or risk damage to your eyes.
- Additionally, the Red Dot Pointer that appears on the material is just a positioning help, not the laser beam itself, however, DO NOT STARE at the Red Dot Pointer or risk damage to your eyes.
- Lastly, the machine doors are safety interlocked and will disable the CO2 laser beam from firing when the doors are opened. The Red Dot Pointer is NOT safety interlocked and can be activated with the door(s) either open or closed.
- Operating the laser cutter in any unsafe way can result in a fine up to the amount of damage caused to the laser cutter. These guidelines are covered in the laser cutter training session. For example, a replacement lens for the XL-12000 costs $800, which costs the school money.
- Unsafe practices include (but are not limited to):
- Leaving the laser cutter unattended while it is running.
- Cutting materials that are not on the acceptable materials list.
Tampering with the laser cutter
- Unsafe practices include (but are not limited to):
- There will be a $200 fine assessed for operating the laser cutter without the appropriate training, with another $200 fine for the person who allowed you access to the system.
- If you are having EID access problems with the laser cutter systems, contact IO Central at 471-1189. Only the IO Staff are permitted to give you access to the system. Do not get another student to log in for you, this can result in the fines listed above.
- Students with outstanding fines will not be permitted to use any IO Central resources until the fines are paid in full.
- Laser cutter reservations must be canceled 12 hours in advance in order to receive a refund. Cancellations within 12 hours will only be refunded if the original reservation holder finds another person to take the reservation. This policy also applies to unused time at the end of a reservation.
- Laser cutter reservations are non-transferable, the person listed on the reservation must be present during the operation of the laser cutter for their reservation. The applies to group projects. The person on the reservation is the person who is officially responsible for the laser cutter during their reservation.
- In the event of laser cutter downtime due to repairs or other unforeseen circumstances, users will be notified by email and reimbursed with a new reservation or on their bevobucks upon their next visit to IO Central
's safety mechanisms.
Turning off the Air Assist feature, especially when vector cutting. Consult with Tech Desk staff for possible exemptions.
- 'Sandwiching' more flammable material between less-flammable materials. (i.e. a sheet of cardboard between two layers of chipboard, etc.) The result could easily be a FIRE!
- IN CASE OF FIRE, IMMEDIATELY PRESS THE EMERGENCY STOP BUTTON (located on top of the laser) AND USE THE FIRE EXTINGUISHER (located near the door).
Using prohibited materials could result in the material melting to the laser cutter bed or releasing toxic fumes. Due to the severity of the risk, cutting prohibited materials will result in loss of lab privileges and fines for damages.
- ABS (3D prints are made with this)
- Foam Core
* Please note that the Co-op sells material that looks like acrylic but is made of PVC and styrene. These materials destroy the optics of the laser and lens, effectively rendering the laser cutter useless.
** Our laser cutters can etch certain coated metals; they cannot cut metal.
ATX Hackerspace also has a list of materials that should never be used for laser cutting: http://atxhackerspace.org/wiki/Laser_Cutter_Materials#NEVER_CUT_THESE_MATERIALS.
Consult with Tech Desk Staff for approval
Wood, ie. plywood with potentially flammable adhesives
Soft materials like leather
For more information on materials that can possibly be cut (not all materials listed are approved by SOA IT), please see: https://www.lasercuttingshapes.com/page/materials.
Another valuable resource: http://atxhackerspace.org/wiki/Laser_Cutter_Materials.