The laser cutters can cut materials up to 1/2" thick, although with some denser materials, no thicker than 1/8" is suggested. The following is a list of acceptable materials with some suggested settings for various acceptable materials, however, exact settings will vary so a materials test should always be performed. The settings provided below should be used only as a reference, since they are settings previously used by our team, but won't necessarily work the same way with your own material.
Also take into consideration that due to natural variations in the pressure of the vacuum, it is expected that the laser cutters might lose power over the day. For example, If you cut something in the morning, it might need a little more power if you cut again in the afternoon.
Prohibited Materials
- Lexan
- Polyurethane
- PVC*
Styrene
- Polycarbonate
- Vinyl
- ABS (3D prints are made with this)
- Foam Core
- Foamboard
- Metal*
Chloride-based materials
Questionable Materials - Consult with Tech Desk Staff for approval
Wood, ie. plywood with potentially flammable adhesives
Soft materials like leather
Reflective materials
Use of prohibited materials could result in the material melting to the laser cutter bed or the release of toxic fumes. Due to the severity in risk, cutting prohibited materials will result in loss of lab privileges and possible fines for damages.
For more information on materials that can possibly be cut (not all materials listed are approved by SOA IT), please see: http://www.lasercuttingshapes.com/page/materials
Another good resource: http://atxhackerspace.org/wiki/Laser_Cutter_Materials
Acceptable Materials - Epilog Fusion Pro 48 CO2 80W
Please do a materials test before every new cutting session to determine the proper levels for your material
| Cut (Vector) | Score/Etch (Vector) | |||||||
|---|---|---|---|---|---|---|---|---|
| Material | Depth | Speed | Power | Frequency | Speed | Power | DPI | Quality & Safety Notes |
| Acetate*** | ||||||||
| Acrylic | 1/8" (3 mm) | 12 | 100 | 100 | 100 | 40 | 300 | Vector cutting table (cross-hatched) must be used. A general rule of thumb for cutting acrylic is to relatively slow speed and high power; this produces a more flame-polished edge. Note from manual: Adjusting the standard focus distance so it is closer to the lens by about .080” (2 mm) will produce better edge quality when cutting 1/4” (6mm) acrylic and thicker. Two passes can be used for cutting thicker materials. There are two types of acrylic: cast is better for engraving (it creates a frosted look when engraved) and extruded acrylic produces a much better flame polished edge. |
| 1/4" (6 mm) | 6 | 100 | 100 | 100 | 60 | 300 | ||
| 3/8" (9.5 mm) | 3 | 100 | 100 | 100 | 55 | 500 | ||
| Alumamark | Engraving | NO | NO | NO | 100 | 20 | 300 | Engrave only. |
| Engraving | NO | NO | NO | 100 | 10 | 500 | ||
| Anodized Aluminum | Photos/Clipart | NO | NO | NO | 100 | 35 | 400 | Engrave only. This material is reflective, so avoid using full power. Use low power and high speed for crisp edges. |
| Photos/Clipart | NO | NO | NO | 100 | 30 | 500 | ||
| Text | NO | NO | NO | 100 | 40 | 500 | ||
| Balsa | ||||||||
| Basswood | 1/16" (1.5 mm) | Charred edges, orange tinting without protective paper masking. | ||||||
| 1/8" (3 mm) | ||||||||
| 3/16" (4.5 mm) | ||||||||
| Bristol | 2 ply | |||||||
| 4 ply | ||||||||
| Chip | 1 ply | 100 | 25 | 50 | 100 | 8 | 50 | |
| 2 ply | 100 | 50 | 50 | 100 | 15 | 50 | ||
| 4 ply | 45 | 90 | 50 | 100 | 50 | 50 | ||
| Cork | 1/8" (3 mm) | NO | NO | NO | 100 | 30 | 300 | Engrave only. |
| 1/4" (6 mm) | NO | NO | NO | 100 | 30 | 50 | ||
| Corrugated cardboard | 1/8" (3 mm) | 100 | 60 | 50 | 100 | 10 | 50 | |
| 1/4" (6 mm) | 60 | 60 | 50 | 100 | 20 | 50 | ||
| Crescent | ||||||||
| Felt | 1/8" (3 mm) | 100 | 40 | 50 | Natural fibers will have charred edges and a strong smell. | |||
| 1/4" (6 mm) | ||||||||
| Fleece | NO | NO | NO | 100 | 15 | 200 | Engrave only. Jarvis dithering pattern is recommended. | |
| Glass | NO | NO | NO | 35 | 100 | 300 | Engrave only. Jarvis dithering pattern is recommended. | |
| Leather | 1/8" (3 mm) | 60 | 100 | 50 | 100 | 20 | 300 | |
| 100 | 25 | 500 | ||||||
| Lucite | ||||||||
| Mat Board | 30 | 40 | 50 | |||||
| MDF (medium-density fibreboard) | 1/8" (3 mm) | Use cutting settings and run 3 times. | ||||||
| Museum Board | 1 ply | 100 | 27.5 | 50 | 100 | 6 | 50 | |
| 2 ply | ||||||||
| 4 ply | 5 | 25 | 50 | Will have some char on edges | ||||
| Mylar | ||||||||
| Regular Paper | ||||||||
| PETG | 1/64" | |||||||
| Plexi (cut twice) | 3/32" | |||||||
| 0.118 | ||||||||
| 1/8" (3 mm) | ||||||||
| 3/16" (4.5 mm) | ||||||||
| Polyester | ||||||||
| Plywood | 1/4" (6mm) (max) | 12 | 100 | 10 | 80 | 50 | 10 | Recent incidents of fire indicate that this material requires caution and additional supervision if cutting is attempted. Additionally, glue pockets may prevent complete cut-through in some areas. |
| Rubber (no-odor) | Must be specially marked for laser cutting. | |||||||
| Strathmore | ||||||||
| Vellum | ||||||||
| Wood | Thin Veneer | 50 | 80 | 10 | Note from manual: When cutting wood, multiple passes may allow cutting of thicker materials. Using Color Mapping you can adjust the focus point between passes down to the center point of the cut for the best results. Always use the additional Sweep Air Assist when cutting. | |||
| 1/8" (3 mm) | 25 | 100 | 10 | |||||
| 1/4" (6mm) | 13 | 100 | 10 | |||||
| 3/8" (9.5 mm) | 7 | 100 | 10 | |||||
| 1/2" (12 mm) | 4 | 100 | 10 | |||||
***Use this setting with caution. Try out a range of settings on a test piece first.
ATX Hackerspace also has a good table of materials for laser cutting reference: http://atxhackerspace.org/wiki/Laser_Cutter_Materials#NEVER_CUT_THESE_MATERIALS
